top of page

How to Determine the Minimum Blank Size

Writer: Durhl Davis
Durhl Davis
Nov 12
5 min read

Updated: 2 days ago


By Durhl Davis, ABO-certified optician, Candor Wholesale Optical Laboratory


Before a lens is ever surfaced, there's one question that decides whether the job will work at all: is the lens blank big enough to cut out the frame shape with the optical centers in the right place?


If the blank is too small, the lens edges out with a missing corner or a gap at the bevel, and the job has to be redone. Calculating the minimum blank size (MBS) takes about a minute and prevents that.


What you need


From the frame:

  • A: the horizontal eye size

  • DBL: the distance between lenses (bridge size)

  • ED: the effective diameter


From the patient:

  • PD: binocular, or monocular for each eye


Step 1: Find the effective diameter (ED), and measure it correctly


Most people think the ED is the longest diagonal across the lens. It isn't, and that mistake is one of the most common reasons a blank comes up short.


What ED actually is: twice the longest radius from the lens's geometric center to its farthest edge. Put another way, it's the smallest circle, centered on the geometric center, that completely encloses the lens shape.


The key words are from the center. A diagonal measured edge to edge doesn't have to pass through the center of the lens, so it can miss the true ED. On a symmetrical rectangle the two come out about the same. On an aviator, a cat-eye or any upswept shape, the farthest corner sits much farther from the center than the opposite side does, and the diagonal reads short.


Where the geometric center is: draw a box around the lens shape, touching the farthest left, right, top and bottom points. That box is A wide and B tall. The geometric center is where the box's horizontal and vertical midlines cross, half the A across and half the B down.

Measuring the ED of a frame is more than the diagonal measurement
Measuring the ED of a frame is more than the diagonal measurement

Three ways to measure ED


1. The tracer (most precise). Trace the frame. Tracers measure the whole shape from its center and report the ED directly. If you have one, use it.


2. A ruler and a marked lens.

  1. Take the demo lens out, or use a pattern.

  2. Draw the box around the shape and mark the center where the midlines cross.

  3. Measure from that center point to the farthest point on the edge. It's usually a corner, but check every corner.

  4. Double it.


Measure the demo lens itself, not the opening in the frame front. The lens is bigger than what you see in the frame because part of its edge sits in the groove or behind the rim.


3. A circle chart. Lay the demo lens on a chart of concentric circles, with the lens's geometric center over the center of the chart. The smallest circle that the entire lens fits inside is the ED.


Example: why the diagonal fools you


An aviator shape: A = 58, B = 50.

  • Measured corner to corner across the lens, the longest diagonal reads 60 mm.

  • With the center marked, the farthest point, the lower outside corner, is 31.5 mm from it.

  • True ED = 31.5 × 2 = 63 mm.


Using the diagonal would have put this job 3 mm short before decentration was even added.


Quick check: if you're in a hurry, adding about 2 mm to the longest diagonal gives a rough estimate. Use it only to sanity-check, not to order. On upswept shapes, it can still fall short.


Step 2: Find the frame PD


Frame PD = A + DBL


This is the distance between the geometric centers of the two lenses in the frame.


Step 3: Find the decentration


Decentration is how far each optical center has to move in from the geometric center of the lens to line up with the patient's pupil.


With a binocular PD: Total decentration = Frame PD − Patient PD


With monocular PDs (more accurate, and better for stronger prescriptions): Decentration per eye = (Frame PD ÷ 2) − Monocular PD


Step 4: Calculate the minimum blank size


MBS = ED + (2 × decentration per eye) + 2 mm


With a binocular PD, that's the same as ED + total decentration + 2 mm.


The 2 mm is an allowance for edging. It's the standard textbook figure, but some lens types, edgers, grooves and wrap frames need more.


Example 1: Binocular PD


  • A = 54, DBL = 18, ED = 58

  • Patient PD = 62


Frame PD = 54 + 18 = 72

Total decentration = 72 − 62 = 10 (5 mm per lens)

MBS = 58 + 10 + 2 = 70 mm


A 65 mm blank won't cut out. Use a 70 mm or larger.


Example 2: Monocular PDs


  • A = 52, DBL = 18, ED = 56

  • Monocular PD: right 31, left 32.5


Frame PD = 52 + 18 = 70, and half of that is 35


Right eye: decentration = 35 − 31 = 4, so MBS = 56 + 8 + 2 = 66 mm

Left eye: decentration = 35 − 32.5 = 2.5, so MBS = 56 + 5 + 2 = 63 mm


Always use the larger number for both lenses, so this job needs at least a 66 mm blank.


A common mistake


Adding only the per-lens decentration once instead of twice gives a blank that's too small. The decentration counts twice because shifting the optical center moves the lens shape toward one edge of the blank, and the blank has to reach on the far side too.


Other things that affect blank size


  • Progressives and multifocals: check the manufacturer's blank sizes and fitting-height requirements. Some designs only come in limited diameters.

  • Specialty lenses: high-index, photochromic, polarized and some coated lenses may not be available in every diameter.

  • Big shapes with strong prescriptions: even when the blank is large enough, a high minus lens in a big frame gets thick at the edges, and a high plus lens gets thick in the center.


If the blank comes up short


  • Choose a frame with a smaller ED, or one with a frame PD closer to the patient's PD.

  • Check whether the lens is available in a larger diameter.

  • Call the lab before you order. We'd rather solve it on the phone than send back a lens that didn't cut out.


How Candor helps


If you're not sure a blank will cut out, call us before you order. We'll run the numbers with you and find a lens and blank size that works.


Questions about a job? Call Durhl at (318) 542-2550 or email info@candoroptical.com. New to Candor? Open a wholesale account and we will follow up within 2–3 business days.

 
 
 

Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
bottom of page